Network Traces.

Here is how to collect a simultaneous network capture between a sending machine and a receiving machine.

Windows

Open an administrative command prompt and run the following command:

md c:\data

netsh trace start capture=yes scenario=netconnection persistent=yes maxsize=1024 tracefile=c:\data\Nettrace.etl

Reproduce the issue

netstat -nato > c:\data\netstat-nato.txt  netsh trace stop

.etl and .cab files with the machine name and IP Address This data can be used to be analyzed using Netmon or wireshark.

Capture a Network Trace without installing anything (capture a network trace of a reboot)

Intro to Filtering with Network Monitor 3.0

“.” (period) 
Tcp.SrcPort == 80
Not equal to 
Tcp.Port!= 80 {! Ignore}
Tcp.SrcPort!= 5555 OR Tcp.DstPort!= 5555
IPv4.Address == 192.168.1.1 

TCPDump:

See the list of interfaces on which tcpdump can listen:

 tcpdump -D

Listen on interface eth0:

 tcpdump -i eth0

Listen on any available interface (cannot be done in promiscuous mode. Requires Linux kernel 2.2 or greater):

 tcpdump -i any

Be verbose while capturing packets:

 tcpdump -v

Be more verbose while capturing packets:

tcpdump -vv

Be very verbose while capturing packets:

tcpdump -vvv

Be verbose and print the data of each packet in both hex and ASCII, excluding the link level header:

tcpdump -v -X

Be verbose and print the data of each packet in both hex and ASCII, also including the link level header:

tcpdump -v -XX

Be less verbose (than the default) while capturing packets:

tcpdump -q

Limit the capture to 100 packets:

tcpdump -c 100

Record the packet capture to a file called capture.cap:

tcpdump -w capture.cap

Record the packet capture to a file called capture.cap but display on-screen how many packets have been captured in real-time:

tcpdump -v -w capture.cap

Display the packets of a file called capture.cap:

tcpdump -r capture.cap

Display the packets using maximum detail of a file called capture.cap:

tcpdump -vvv -r capture.cap

Display IP addresses and port numbers instead of domain and service names when capturing packets (note: on some systems you need to specify -nn to display port numbers):

tcpdump -n

Capture any packets where the destination host is 192.168.1.1. Display IP addresses and port numbers:

tcpdump -n dst host 192.168.1.1

Capture any packets where the source host is 192.168.1.1. Display IP addresses and port numbers:

tcpdump -n src host 192.168.1.1

Capture any packets where the source or destination host is 192.168.1.1. Display IP addresses and port numbers:

tcpdump -n host 192.168.1.1

Capture any packets where the destination network is 192.168.1.0/24. Display IP addresses and port numbers:

tcpdump -n dst net 192.168.1.0/24

Capture any packets where the source network is 192.168.1.0/24. Display IP addresses and port numbers:

tcpdump -n src net 192.168.1.0/24

Capture any packets where the source or destination network is 192.168.1.0/24. Display IP addresses and port numbers:

tcpdump -n net 192.168.1.0/24

Capture any packets where the destination port is 23. Display IP addresses and port numbers:

tcpdump -n dst port 23

Capture any packets where the destination port is is between 1 and 1023 inclusive. Display IP addresses and port numbers:

tcpdump -n dst portrange 1-1023

Capture only TCP packets where the destination port is is between 1 and 1023 inclusive. Display IP addresses and port numbers:

tcpdump -n tcp dst portrange 1-1023

Capture only UDP packets where the destination port is is between 1 and 1023 inclusive. Display IP addresses and port numbers:

tcpdump -n udp dst portrange 1-1023

Capture any packets with destination IP 192.168.1.1 and destination port 23. Display IP addresses and port numbers:

tcpdump -n "dst host 192.168.1.1 and dst port 23"

Capture any packets with destination IP 192.168.1.1 and destination port 80 or 443. Display IP addresses and port numbers:

tcpdump -n "dst host 192.168.1.1 and (dst port 80 or dst port 443)"

Capture any ICMP packets:

tcpdump -v icmp

Capture any ARP packets:

tcpdump -v arp

Capture either ICMP or ARP packets:

tcpdump -v "icmp or arp"

Capture any packets that are broadcast or multicast:

tcpdump -n "broadcast or multicast"

Capture 500 bytes of data for each packet rather than the default of 68 bytes:

tcpdump -s 500

Capture all bytes of data within the packet:

tcpdump -s 0

So you want to use Wireshark to read the netsh trace output .etl?

Advertisements